Posts Tagged With: Ultimaker

Upgrade: Print without a pc for less than 10€ (part 1)

Ever wanted to run your 3D printer directly from SD card? This hack enables you to print from an SD card without the need of a PC.
Basically all you need to do is a cable to connect a SD module to your printer, but in this post I’m also going to show you how to create/adapt a SD module in case you don’t already have one.

You can use any SD module you like. MicroSD, SD, or even build your own! I'll show you how

You can use any SD module you like. MicroSD, SD, or even build your own! I’ll show you how

Despite I’m working on a control panel with some innovative features (look here), I’ve been asked to publish a super-cheap solution that can make you print without the need of a pc (or like in my case a Mac).
Printing without the need of a PC has many benefits, the first one of course it’s that… well… you don’t need a PC.
It could seem a stupid thing to say, but when you have to print a big file and you want to use your pc, you realize it’s not that banal after all 😉

Notice that Marlin firmware already supports a feature called “autostart” to automatically print a file from a SD card, but in my opinion it needs some improvments to make it more reliable for the scope we want.
This first post (of 3) will illustrate the “hardware” part of the solution: the SD card reader and how to build the cable to connect it to your printer.
Part two will be about the changes of the firmware, and part three will be about how to provide an enclosure and some improvements for a even better experience.

SKILL: not for a rookie  if you want to build your own SD board, otherwise: not difficult at all
TIME: from 1 to 3 hours, depending on the options
TOOLS: a soldering iron, hot glue (optional)
COMPONENTS: 1 SD card module (or components to build it), 30cm of 10 wire ribbon cable, 1 2×5  female Molex connector, 10 female plugs
OPTIONAL COMPONENTS: 
1 LED, 1 resistor, 1 push button (see part 3)

Continue reading

Advertisements
Categories: 3D Printer, Improvements | Tags: , , , , , , , , , | Leave a comment

Upgrade: Mod your POWERWASP to support variable fan speed

A controllable fan (on/off and speed) it’s a nice feature that really improves your prints and, once setup, it can operate without any assistance.
In the POWERWASP, fan is directly connected to the regulated 12v output that’s always on. Since this printer it’s really well made you can attach or detach you fan anytime, also during the print, basically turning it on and off as you like. For example you can add the fan after the firsts layer, but still you need to assist you printer and… is just off or full power. To take advantage of the features of your slicer software (like cura or slic3r) and your Marlin firmware, just follow this tutorial.
After your hardware upgrade you may want to update your firmware to support this feature in a better way, but I will tell you about this later on.

SKILL: some confidence with your printer and ability to solder trough holes components
TIME: 1h (actually I don’t remember how much it took, but it’s more than reasonable)
TOOLS: nothing special, just scissors, screwdriver and a soldering iron
COMPONENTS: one BD679 transistor and one 1k resistor

The POWERWASP printer comes with an Utlimaker shield clone (rev. 1.5.4) that uses a dedicate pwm pin (D7 on Arduino) to operate the fan to cool the hot-end.
You can find more info and schematics here: http://reprap.org/wiki/Ultimaker%27s_v1.5.4_PCB

Ultimaker shield rev. 1.5.4

Ultimaker shield rev. 1.5.4

Power Wasp Shield

POWERWASP shield

As you can see from the pictures above the two boards are identical except for one thing: the POWERWASP shield has all the components needed to run the printer and not those unused (in perfect WASP style ;-)) so to run this feature I had to add them by myself. A really easy operation if you know how to solder trough hole components.

Step 1:
Open the cover on the bottom of the POWERWASP and disconnect all the wires from the shield (I suggest you to mark them carefully to easily put them back on the right places 😉

Step 2:
Cut the power supply wires that are directly soldered on the pcb. Once terminated the mod, instead of solder them back, I added a connector just in case I will ever need to remove the board again, but that’s optional: you can just solder them back to the pcb without any problem.

PowerWasp shield update for variable speed fan

POWERWASP shield modified to use pin 7 to control a variable speed fan. Sorry I took this picture upside down compared to the others…

Step 3:
Solder the transistor BD679 in the right position (see picture “number 1”) (Q4 in Ultimaker pcb schematics) Continue reading

Categories: 3D Printer, Improvements | Tags: , , , , | 4 Comments

Blog at WordPress.com.